X-ray timelapse of fluid movement in plants, stop-motion animation, sensor teardown/repair

I repaired a large digital x-ray detector and used it to record timelapse and stop-motion animations of plants, a clock, and a camera lens.

Applied Science X-ray backscatter imaging system: https://www.youtube.com/watch?v=H7ldYhzKAp4

Applied Science CT scanner: https://www.youtube.com/watch?v=hF3V-GHiJ78 

Geiger counter: https://mightyohm.com/blog/products/geiger-counter/ 

Linistepper motor driver: http://www.massmind.org/techref/io/stepper/linistep/lini_use.htm 

Potassium iodide: https://www.amazon.com/dp/B01JKJWXBK 

GE Rhythm user guide: https://www.bakerhughesds.com/sites/g/files/cozyhq596/files/2018-07/rhythm_rt_manual_english_rev_e.pdf 

Octave (open source MATLAB alternative): https://www.gnu.org/software/octave/index 

Mouse movement recorder software: https://sourceforge.net/projects/mousecontroller/ 

Octave and Arduino code used in this video: https://drive.google.com/drive/folders/1vM6KSc_EhrKc8J92Yn_-PE-lZhL3gkhA?usp=sharing 

Thank you for your support on Patreon: https://www.patreon.com/AppliedScience 

Thank you, Amir, for the X-ray sensor and software!

Underwater laser cutting and silver sintering to make ceramic circuit boards

 

Thermal stress cracking can be completely avoided by CO2 laser cutting thin alumina sheets underwater.  I also show how to formulate and apply silver paste, then sinter in a kiln to produce double-sided ceramic printed circuit boards with conductive vias.

60W CW CO2 laser at 80% power.  10mm/sec.  Standard lens focal length (50mm).  2mm water above ceramic.  180 passes to cut through 0.75mm thick alumina.  

Silver paste: 97% silver powder, 3% glass powder by mass.  Particle size 1 micron or less. Add poly vinyl alcohol mold release until desired consistency reached.

Paste applied with 4 mil thick vinyl stencil.  Dried in air 10 minutes, then rapidly brought up to 900*C, held for 10 minutes, then rapidly brought back down to room temperature.  Total cycle about 45 minutes.

I measured electrical conductivity of the finished traces from my process with vinyl stencils: 4 milliohms per square at 10 micron final thickness.  This is pretty close to the Dupont published spec ( less than 2 milliohm/sq at 16 micron thick)

Underwater CO2 laser cutting reference: https://sci-hub.se/10.1016/J.JEURCERAMSOC.2011.06.015

60W laser cutter: https://www.ebay.com/itm/294386493292

Ceramic sheets at McMaster: https://www.mcmaster.com/alumina/nonporous-alumina-ceramic-sheets-and-bars/

Ceramic PCB prototypes: https://ceramic-pcb.com/product/alumina-pcb-al2o3-pcb-prototypes-online/

Quickfire kiln: https://kruegerpottery.com/products/par_quikfire6

Raspberry Pi picoReflow oven controller: https://apollo.open-resource.org/mission:resources:picoreflow

Silver powder: https://www.ebay.com/itm/122525930519

Glass glaze: https://www.amazon.com/dp/B0044SCR6O

Macor: https://www.mcmaster.com/materials/material~glass-mica-ceramic/

Dupont silver paste: https://www.dupont.com/content/dam/dupont/amer/us/en/transportation-industrial/public/documents/en/LF131.pdf

Binders for ceramic powder: https://digitalfire.com/article/binders+for+ceramic+bodies

PVA mold release: https://www.tapplastics.com/product/fiberglass/mold_releases/tap_pva_mold_release_liquid/67

Applied Science on Patreon: https://www.patreon.com/AppliedScience

Atomic Layer Deposition of copper - If you like sputtering, you'll love this!

 

An explanation and demo of atomic layer deposition (ALD) of copper metal on glass.  Precursors are copper(I) chloride and hydrogen, processed in a hot-wall tube quartz tube furnace.

10 torr operating pressure

500 sccm argon sweep/purge gas constantly flowing

75 sccm CuCl argon pulse gas (17 seconds including flow controller lag)

100 sccm H pulse gas (14 seconds including flow controller lag)

7 second purge time between pulses

100mm quartz tube furnace diameter 

415*C deposition temperature

350*C CuCl evaporation temperature

Substrates are mostly borosilicate glass cleaned with RCA clean

The "good" samples shown in the video are about 750 cycles (about 9 hours

Main ref:

https://sci-hub.se/https://doi.org/10.1002/cvde.19970030107

Also helpful:

https://sci-hub.se/https://doi.org/10.1063/1.5087759

https://sci-hub.se/10.1149/2.0261501jss

https://sci-hub.se/https://doi.org/10.1016/0022-0248(92)90191-K

Alicat flow controller manuals (hard to find via website navigation):

https://documents.alicat.com/manuals/DOC-MANUAL-MC.pdf

https://documents.alicat.com/manuals/old/Gas_Flow_Controller_Manual_rev7.pdf

https://documents.alicat.com/Alicat-Serial-Primer.pdf

RCA clean: https://en.wikipedia.org/wiki/RCA_clean

CuCl synthesis: http://wwwchem.uwimona.edu.jm/lab_manuals/c1901exp35.html

Support Applied Science on Patreon: https://www.patreon.com/AppliedScience

The best projects from 10 years of Applied Science

 Liquid oxygen BBQ - https://www.youtube.com/watch?v=1bjvj5FjUPE

Fondant cake making - https://www.youtube.com/watch?v=_IhibizyrtU

Scanning Electron Microscope - https://www.youtube.com/watch?v=VdjYVF4a6iU

Transcranial magnetic Stimulation - https://www.youtube.com/watch?v=B_olmdAQx5s

Supercritical CO2 chamber - https://www.youtube.com/watch?v=-gCTKteN5Y4

LED in a contact lens - https://www.youtube.com/watch?v=qHECpEhJdB8

Pop Rocks candy - https://www.youtube.com/watch?v=qsSwvmNEr0Q

X-Ray backscatter - https://www.youtube.com/watch?v=H7ldYhzKAp4

X-Ray CT - https://www.youtube.com/watch?v=hF3V-GHiJ78

Cookie Perfection Machine - https://www.youtube.com/watch?v=8YEdHjGMeho

LCD - https://www.youtube.com/watch?v=_zoeeR3geTA and https://www.youtube.com/watch?v=d4QFNWBSZYg

Vinyl LP in electron microscope - https://www.youtube.com/watch?v=GuCdsyCWmt8

Silicon etching rugate optical filters - https://www.youtube.com/watch?v=iwj78pR46zM

https://www.patreon.com/AppliedScience

Measuring human digestive efficiency vs. a flame

 "200 Calories" on a nutrition label doesn't describe the total flammable caloric content. I explore the differences between digestible and flammable calories using a homemade calorimeter with glass windows.

Pressure sensor: https://www.digikey.com/en/products/detail/te-connectivity-measurement-specialties/M5842-000005-10KPG/7592854 Schedule 160 pipe on McMaster: https://www.mcmaster.com/7733K259/ 32 ga nichrome wire: https://www.amazon.com/gp/product/B07DL4DSWD/ Power supply (used for ignition wire): https://www.amazon.com/gp/product/B07SS77N7K/ Keithley 6.5 digit multimeter: https://www.tek.com/tektronix-and-keithley-digital-multimeter/dmm6500 Tek MSO 4 series oscilloscope: https://www.tek.com/oscilloscope/4-series-mso-mixed-signal-oscilloscope Soylent: https://soylent.com/ Support Applied Science on Patreon: https://www.patreon.com/AppliedScience

Prototyping with Applied Science: Design and build a bite sensor

Join me in brainstorming and building a bite force sensor that allows paraplegic musicians to smoothly control an expression pedal. This video will include construction tips and tricks, methods, material selection, and a little design philosophy.

Tiny linear potentiometer used in final design: https://www.digikey.com/en/products/detail/bourns-inc/3046L-1-103/3781580 Spring-loaded linear potentiometer: https://www.digikey.com/en/products/detail/tt-electronics-bi/404R10KL1-0/2408603 Sil-Poxy for bonding silicone rubber to itself and other materials: https://www.smooth-on.com/product-line/sil-poxy/ Sorta Clear 40 - Platinum-cure silicone molding: https://www.smooth-on.com/products/sorta-clear-40/ Light-cure 3311 adhesive: https://www.mcmaster.com/1700A253/ (expensive, but this tube will last a long time) Blue lasers on eBay "5mW" *wink* https://www.ebay.com/itm/3-Packs-900Mile-Strong-Laser-Pointer-Pen-Green-Blue-Red-Light-Visible-Beam-Lazer/174479770737 Braided shield, highly flexible, 4-conductor cable: https://www.digikey.com/en/products/detail/tensility-international-corp/30-00218/5270175 Fabric reinforced silicone sheet: https://www.mcmaster.com/8612K51/ Mechanical CAD on github: https://github.com/benkrasnow/BiteSensor Support Applied Science on Patreon: https://www.patreon.com/AppliedScience